MEN Mikro Elektronik F302-3U User Manual download pdf

Embedded Solutions

for Transportation and Industrial Markets

www.men.de/products/02F302-.html

F302 – 3U CompactPCI

Industrial Ethernet

Switch

n Managed 8+1-Port rugged Ethernet switch

n 12 or 16 HP 32-bit/33-MHz CompactPCI

n 8 Fast Ethernet ports (front) on RJ45 or

M12 connectors

n Configuration via Telnet CLI, SNMP ver. 3

or external dongle

n Switch accessible via cPCI for router

applications

n Service interface via D-Sub

n LEDs for port and board states

n -40 to +85°C with qualified components

n EN 50155 compliant (railways)

The F302 is a managed 3U Fast Ethernet switch module

with a maximum of eight channels at the front panel (8

RJ45 or M12 connectors) plus one additional Ethernet

channel that is led to the CompactPCI

J1 connector at

the rear.

The F302 is managed by its own PowerPC

CPU that

integrates the configuration firmware. A service

interface is accessible at the front panel, providing an

easy way to configure the switch. A command line

interface is available via the RS232 at the service port

and over Ethernet via Telnet or Secure Shell (SSH). The

switch can also be configured via SNMP (version 3).

Additionally, the service connector can be used to

attach an external dongle to store or update the switch

configuration. This makes it easy to exchange the unit

for service purposes.

The F302 supports full-duplex and half-duplex

operation with auto-negotiation, high-speed non-

blocking store-and-forward-switching, Quality of

Service (QoS) support with four traffic classes IEEE 802.1p and three-

level 802.1x security as well as the logical segmentation of ports

(802.1q VLANs). The switch is fault tolerant and restores itself on its

own: If a link is temporarily unavailable, frames can be sent via backup/

redundant links (spanning tree protocol / link aggregation) and no data

loss occurs. Its built-in test mechanisms make the F302 an even more

reliable component in the communication system.

The F302 was specifically designed for rugged mobile communication

systems. It is thus for example fully compliant with the EN 50155

railway standard. All components on the board are specified for a -40 to

+85°C operation temperature. There are no socketed components,

hardening the card against shock and vibration. The board is ready for

coating (standard with M12 connectors) and has a guaranteed

minimum standard availability of 5 years.

Depending on the connector type, the F302 has a front-panel width of

12 HP (3 slots) with RJ45 or 16 HP (4 slots) with M12 connectors. In

either case the card occupies only one CompactPCI

backplane slot.

F302 Data Sheet / 2013-04-19 Page 1

1 2 3 4 5 6

Summary of Contents

Page 1 - Industrial Ethernet

Embedded Solutionsfor Transportation and Industrial Marketswww.men.de/products/02F302-.htmlF302 – 3U CompactPCI® Industrial EthernetSwitchn Managed 8+

Page 2 - Embedded Solutions

Embedded Solutionsfor Transportation and Industrial Marketswww.men.de/products/02F302-.htmlDiagramCompactPCI® J1Switch Device10/100Base-TPort 6Port 4P

Page 3 - Technical Data

Embedded Solutionsfor Transportation and Industrial Marketswww.men.de/products/02F302-.htmlTechnical DataKey Features n Simple Switch replacement: con

Page 4

Embedded Solutionsfor Transportation and Industrial Marketswww.men.de/products/02F302-.htmlTechnical DataCompactPCI® Bus n Compliance with CompactPCI®

Page 5 - Ordering Information

Embedded Solutionsfor Transportation and Industrial Marketswww.men.de/products/02F302-.htmlConfiguration & OptionsStandard ConfigurationsArticle N

Page 6 - Contact Information

Embedded Solutionsfor Transportation and Industrial Marketswww.men.de/products/02F302-.htmlContact InformationGermanyMEN Mikro Elektronik GmbHNeuwiede